Advice

Air conditioning for shops: what size unit do you need?

Learn how to size portable air conditioning for a shop, assess doors, glazing and equipment, and decide when one unit or a specialist assessment is needed.

One unit may suit a small enclosed shop, not every sales floor

A 12,000–14,000 BTU/h portable air conditioner may suit a small, enclosed shop or a defined staff area, but it is not a reliable whole-shop recommendation without checking the space. A larger sales floor, sunny frontage or frequently open entrance may need several units or a different system. Size the cooling to the heat entering and being produced inside, rather than floor area alone.

That capacity range is approximately 3.5–4.1 kW of cooling per unit. It describes heat removal, not electricity consumption: use the unit’s electrical specification when checking its power requirements. Cooling capacity is commonly shortened to BTU in product descriptions, although BTU/h is the relevant rating.

For air conditioning for shops, any quoted room coverage should be treated as a starting point, not a promise. Before choosing a unit, establish the floor area, ceiling height, glazing, door use, internal heat sources and exhaust route. If whole-store temperature control matters, ask a competent air-conditioning professional for a cooling-load assessment.

Measure the area that actually needs cooling

Measure the connected space you intend to cool, not just the area listed on the lease. Record its length, width and ceiling height, then identify stockrooms, staircases and other spaces connected through open doorways. A rear room with its door shut presents a different cooling task from one permanently open to the sales floor.

For example, a rectangular sales area measuring 8 metres by 5 metres has a floor area of 40 square metres. That is a useful measurement to give a supplier, but it does not establish the required capacity. The same floor area could have shaded windows and a closed entrance, or extensive sunlit glazing and constant customer traffic.

Sketch the layout, including tall shelving, counters and partitions. These can stop cooled air reaching occupied areas even when the nominal capacity appears adequate. Record unusually high ceilings too: a simple floor-area estimate does not capture the geometry or airflow of the space.

Check the frontage, entrance and equipment before choosing capacity

Sunlight, outside air and equipment can change the cooling requirement substantially. Note which windows receive direct sun and when, whether shading is available, and whether the entrance is normally closed, frequently opened or held open throughout trading. Assess the conditions during the busiest, sunniest period rather than an empty morning.

List heat-producing equipment operating in the space, including lighting, display screens, preparation appliances and refrigeration. A plug-in refrigerator commonly releases heat through its condenser into the shop, while equipment with an external condenser behaves differently. Do not simply add appliance nameplate ratings together and assume the result is the cooling load; actual operation needs consideration.

Include staff numbers and typical customer occupancy in the brief. Reduce avoidable gains where practical: use suitable shading, switch off unnecessary equipment and keep external doors closed when compatible with access and shop operation. These steps can make cooling more effective, but they cannot replace adequate capacity where heat gains remain high.

Choose between whole-store cooling and a cooler working area

Decide whether the aim is to cool the entire shop or improve conditions around a particular counter or workstation. This decision affects the capacity required, placement and whether portable equipment is realistic. A unit directed towards a checkout may improve local comfort without maintaining the same temperature throughout the premises.

In an open-plan shop, a cooling zone is not a separate room: air mixes and heat continues to move into it. A genuinely enclosed office or service room is easier to control. Do not promise a particular temperature at one end of a sales floor simply because a unit has been positioned there.

Several units can distribute cooling more effectively around obstacles, but their ratings are not the whole answer. Two 12,000 BTU/h units have a combined nominal capacity of about 7 kW, yet each still needs suitable power, exhaust arrangements and airflow. Poor placement or substantial outside-air entry can undermine the result.

Prove the exhaust route before ordering

A portable air conditioner needs a suitable way to discharge its hot exhaust outdoors. Check this before deciding how many units to hire. Venting into a stockroom, ceiling void or another part of the shop transfers the problem elsewhere and can allow heat to return to the cooled area.

Identify a suitable window or other approved outlet and check the proposed hose arrangement against the model’s instructions. Keep the hose within the permitted length and avoid crushing or tight bends. Seal the opening around the outlet as effectively as the installation allows; a wide-open window beside the hose admits unwanted outside air.

Many single-hose units exhaust air taken from the room, which draws replacement air into the space through available openings. This matters particularly around open entrances and leaky shopfronts. Also check that the outlet position, window security and any alterations are acceptable to the landlord or building manager. Never obstruct an escape route to accommodate equipment.

Build a sizing brief in one walkthrough

Prepare a short written brief before requesting a recommendation. Start with measured dimensions, ceiling height and a simple plan showing connected rooms, entrances and windows. Add photographs of the frontage, intended unit positions and possible exhaust outlets. This helps distinguish a capacity problem from an installation constraint.

Next, record operating conditions: trading hours, sunny periods, door-opening patterns, typical occupancy and equipment running during the hottest part of the day. State whether existing cooling is working, partly working or unavailable. Explain the required outcome, such as improving checkout conditions or cooling the whole sales floor.

Finally, inspect practical access and services. Note available sockets, delivery access, steps, storage space and a possible condensate-management arrangement. Ask the supplier to confirm the proposed models, capacity, hose requirements and operating instructions. Where several units are proposed, have a competent person confirm that the electrical arrangements can support them rather than assuming spare sockets mean spare capacity.

Judge performance during trading, away from the cold outlet

Check the result where people work and shop, not immediately in front of the unit. Place thermometers at representative occupied positions, away from direct sunlight, hot equipment and the discharge air. Record conditions before operation and through the trading day so that a brief blast of cold air is not mistaken for effective room cooling.

Use the cooling mode and settings recommended for the unit, and allow it time to affect the space. Where appropriate, start before heat has built up rather than waiting until the premises are already uncomfortable. Keep the air inlet and discharge clear of displays, packaging and hanging merchandise.

If temperatures remain unsatisfactory, check the exhaust seal, hose, filters, doors and condensate warnings before requesting more capacity. Compare readings across the shop: one cool area and one hot area suggest a distribution problem; poor results throughout may indicate excessive heat gain or insufficient capacity. Reassess under comparable trading conditions where possible.

Recognise when portable cooling is the wrong fit

Portable units may not be a workable whole-shop solution where entrances stay open, heat-producing processes are substantial or no suitable outdoor exhaust route exists. Increasing the number of units does not remove those constraints. Large, interconnected or regularly overheating premises warrant a professional assessment of the building and cooling options.

Common mistakes include selecting solely by floor area, confusing electrical input with cooling output, extending exhaust hoses beyond the manufacturer’s limits and placing units behind merchandise. Avoid improvised electrical arrangements, and do not assume a comfort-cooling unit can maintain temperatures required for food, medicines or other sensitive stock.

For a recurring seasonal problem, compare temporary cooling with a properly designed permanent installation, including ventilation, maintenance, permissions and disruption. Portable air conditioning can provide useful temporary capacity, but it does not generally replace fresh-air ventilation. Where ventilation or product-storage conditions are critical, seek advice from the relevant qualified professional.

Common questions

Will setting the thermostat much lower cool the shop faster?

A lower setpoint does not increase the unit’s rated cooling capacity. It may simply keep cooling running for longer. Select an appropriate target and investigate heat gains, airflow and installation if the shop is not approaching it.

Can a portable unit cool fitting rooms behind curtains?

Possibly, but curtains and partitions can restrict air movement, leaving fitting rooms warmer than the surrounding shop. Check temperatures inside them and discuss placement with the supplier. Do not assume the main sales-floor reading represents enclosed changing areas.

Will staff need to empty a water tank?

Condensate handling varies by model and operating conditions. Some units evaporate some moisture through the exhaust but may still require draining. Confirm tank checks, shutdown behaviour and any drain requirements before installation, and assign responsibility for monitoring during trading.

How should a shop assess noise before hiring?

Ask for the specific model’s sound information and available operating modes. Consider its position relative to payment conversations, consultations and quiet retail areas. Compare sound figures only where measurement conditions are comparable; a generic description such as 'quiet' is not enough.

Can a fan reduce the air-conditioning capacity required?

A fan does not remove heat from the shop, so it should not be deducted from the calculated cooling requirement. It can help circulate cooled air and improve comfort locally. Position it without blocking access or directing air against the conditioner’s intended airflow.

Need air conditioning?

WHEN YOU NEED IT. WE'RE THERE.

Portable air conditioning delivered to your home or business.

Or send a full enquiry